Index: DamClients/DamLive/trunk/doc/DAMLive - Functional Design/DAMLive_Intro.tex
===================================================================
diff -u -r5837 -r6335
--- DamClients/DamLive/trunk/doc/DAMLive - Functional Design/DAMLive_Intro.tex	(.../DAMLive_Intro.tex)	(revision 5837)
+++ DamClients/DamLive/trunk/doc/DAMLive - Functional Design/DAMLive_Intro.tex	(.../DAMLive_Intro.tex)	(revision 6335)
@@ -57,14 +57,13 @@
 The generation of the DAM project file is described in the Functional Design of DAM UI, see \citep{DAMUI_FunctionalDesign}.
 In this DAM project information containing situation information about the sensors; where are the sensors placed and for which PL-line is the data used.
 
-The sensordata itself (the measurements0 must be provided in xml format.
+The sensordata itself (the measurements) must be provided in xml format.
 For DAM-FEWS is this described in the FEWS Public Wiki: https://publicwiki.deltares.nl/display/FEWSDOC/Delft-Fews+Published+Interface+timeseries+Format+Import.
 
 \section{REQ Calc.Settings}\label{sec:REQCalcSettings}
 \ProgramName can use the kernels which are used by DAM Engine. 
 The user can change the calculations settings, such as which failure mechanisms (kernels) and models to use, via an XML file.
-The available failure mechanisms and models are described in the Functional Design of DAM Engine \citep{
-DAMEngine_FunctionalDesign}.\newline
+The available failure mechanisms and models are described in the Functional Design of DAM Engine \citep{DAMEngine_FunctionalDesign}.\newline
 Available for DAM live are:
 
 \begin{table}[H]
@@ -74,9 +73,45 @@
 Calculation models for Stability & Bishop\newline UpliftVan\newline BishopUpliftVan  \\ \hline
 Search methods for Stability & Grid\newline BeeSwarm \\ \hline
 \end{tabular}
-\caption{\small \ProgramName calculation settings.}
+\caption{\ProgramName calculation settings in the parameters xml file}
 \end{table}
 
+The user can also change the grid and tangent lines settings, the path of the working directory or the water level offset via the configuration file \textit{DamLive.dll.config}, 
+located next to the DAMLive executable.
+
+\begin{table}[H]
+\begin{tabular}{|p{82mm}|p{\textwidth-82mm-24pt}|} \hline
+\textbf{Parameter} & \textbf{Options/Default} \\ \hline
+SlipCircleBishopSearchAreaDetermination & Specified (default) \newline Automatic \\ \hline
+SlipCircleBishopGridVerticalPointCount & 10 (default)\\ \hline
+SlipCircleBishopGridVerticalPointDistance & 2.5 (default)\\ \hline
+SlipCircleBishopGridHorizontalPointCount & 10 (default)\\ \hline
+SlipCircleBishopGridHorizontalPointDistance & 2.5 (default)\\ \hline
+
+SlipCircleUpliftVanGridSizeDetermination & Specified (default) \newline Automatic \\ \hline
+SlipCircleUpliftVanLeftGridVerticalPointCount & 10 (default)\\ \hline
+SlipCircleUpliftVanLeftGridVerticalPointDistance & 2.5 (default)\\ \hline
+SlipCircleUpliftVanLeftGridHorizontalPointCount & 10 (default)\\ \hline
+SlipCircleUpliftVanLeftGridHorizontalPointDistance & 2.5 (default)\\ \hline
+SlipCircleUpliftVanRightGridVerticalPointCount & 3 (default)\\ \hline
+SlipCircleUpliftVanRightGridVerticalPointDistance & 2.5 (default)\\ \hline
+SlipCircleUpliftVanRightGridHorizontalPointCount & 6 (default)\\ \hline
+SlipCircleUpliftVanRightGridHorizontalPointDistance & 2.5 (default)\\ \hline
+
+SlipCircleUpliftVanTangentLinesDefinition & OnBoundaryLines (default) \newline Specified \newline Automatic \\ \hline
+SlipCircleUpliftVanTangentLinesDistance & 0.25 (default) \\ \hline
+
+StabilityWorkingPath & \\ \hline
+PipingWorkingPath & \\ \hline
+WaterLevelOffset & \\ \hline
+\end{tabular}
+\caption{\ProgramName grid and tangent lines settings in the \textbf{DamLive.dll.config} file}
+\end{table}
+
+These settings are described in the Functional Design of DAM Engine \citep{DAMEngine_FunctionalDesign}.
+
+\Note{The configuration file \textit{Deltares.Dam.Data.dll.config} contains also grid and tangent lines settings 
+but these settings are overwritten by the settings defined in the \textit{DamLive.dll.config} file.}
  
 \section{REQ Data.Output}\label{sec:REQDataOutput}
 \ProgramName can produce output files.