Index: DamClients/DamUI/trunk/doc/DAM UI - User manual/DAM UI - User manual.tex
===================================================================
diff -u -r4535 -r4536
--- DamClients/DamUI/trunk/doc/DAM UI - User manual/DAM UI - User manual.tex	(.../DAM UI - User manual.tex)	(revision 4535)
+++ DamClients/DamUI/trunk/doc/DAM UI - User manual/DAM UI - User manual.tex	(.../DAM UI - User manual.tex)	(revision 4536)
@@ -2251,13 +2251,15 @@
 In de mode calamiteiten en ontwerp kunnen globale rekeninstellingen worden ingesteld (op waterschapsniveau). 
 
 \paragraph*{Glijvlakmodel}
-DAM kan gebruik maken van de volgende rekenmodellen:
+DAM kan gebruik maken van de volgende rekenmodellen voor \textit{Stability Inside}:
 \begin{itemize}[noitemsep, nolistsep]
 	\item Bishop
 	\item Uplift Van
 	\item Bishop/Uplift Van
 \end{itemize}
 
+Hiernaast biedt DAM 1 model (\textit{Bishop}) aan voor \textit{Stability Outside}.  
+
 \paragraph*{Gridinstellingen}
 Er zijn verschillende opties mogelijk:
 \begin{itemize}[noitemsep, nolistsep]
Index: DamClients/DamUI/trunk/doc/DAM UI - Functional Design/DataFormat.tex
===================================================================
diff -u -r2584 -r4536
--- DamClients/DamUI/trunk/doc/DAM UI - Functional Design/DataFormat.tex	(.../DataFormat.tex)	(revision 2584)
+++ DamClients/DamUI/trunk/doc/DAM UI - Functional Design/DataFormat.tex	(.../DataFormat.tex)	(revision 4536)
@@ -35,7 +35,10 @@
 location$\_$scenario$\_$id & All scenarios with missing location$\_$scenario$\_$id are not imported and message is given. \\ \hline
 characteristic points (required) & All locations with missing required characteristic points are not imported and message is given. \\ \hline
 crosssection (via shape) & All locations with missing cross section are not imported and message is given. \\ \hline
+SigmaTau curve (via csv) & When needed (as defined in the soils.csv) the curves must each meet the validation requirements as given in OverviewDataUIAndEngine.xlsx. All incorrect curves are not imported and a message is given. \\ \hline
 \end{tabular}
+
+
 \caption{Exception handling required data during import}
 \label{table:ExceptionHandlingReqData}
 \end{table}
Index: DamClients/DamUI/trunk/doc/DAM UI - Functional Design/CalcSettings.tex
===================================================================
diff -u -r3660 -r4536
--- DamClients/DamUI/trunk/doc/DAM UI - Functional Design/CalcSettings.tex	(.../CalcSettings.tex)	(revision 3660)
+++ DamClients/DamUI/trunk/doc/DAM UI - Functional Design/CalcSettings.tex	(.../CalcSettings.tex)	(revision 4536)
@@ -2,13 +2,15 @@
 All calculation settings are the same for all dike rings and locations within the project. So there is only one set of calculation settings.
 
 \section{Macrostability}\label{sec:Macrostability}
-In DAM the following piping models can be used:
+In DAM the following models for Stability Inside can be used:
 \begin{itemize}
 	\item \textit{Bishop}
 	\item \textit{UpliftVan}
 	\item \textit{Bishop-UpliftVan}
 \end{itemize}
 
+Next to Stability Inside, one model (\textit{Bishop}) is offered for Stability Outside.
+
 Note that for both \textit{Bishop} and \textit{UpliftVan} a brute force search method based on moving grids is offered. 
 For \textit{UpliftVan}, 
 the search method \textit{Bee Swarm} is an alternative option.
@@ -36,8 +38,6 @@
 In DAM the following piping models can be used:
 \begin{itemize}
 	\item Bligh
-	\item Sellmeijer VNK
-	\item Sellmeijer 4 forces
 	\item Sellmeijer revised (WBI)
 \end{itemize}
 
Index: DamClients/DamUI/trunk/doc/DAM UI - Functional Design/DataDisplay.tex
===================================================================
diff -u -r3431 -r4536
--- DamClients/DamUI/trunk/doc/DAM UI - Functional Design/DataDisplay.tex	(.../DataDisplay.tex)	(revision 3431)
+++ DamClients/DamUI/trunk/doc/DAM UI - Functional Design/DataDisplay.tex	(.../DataDisplay.tex)	(revision 4536)
@@ -31,8 +31,8 @@
 
 
 \section{Map}\label{sec:map}
-Show the locations as a dot on a map with Open street map as background. 
-Background can also be empty.
+Show the locations as a dot on a map with a PDOK map as background (when selected). 
+The background can also be empty.
 Display imported shapefiles when selected by user.
 
 \section{General}\label{sec:DisplayGeneral}
Index: DamClients/DamUI/trunk/data/DamEngineTestProjects/OverzichtDataDAM.xlsx
===================================================================
diff -u -r4524 -r4536
Binary files differ